China powder coating Suppliers, China powder coating Manufacturers.

ChemNet  |   Sign in  |   Join Now
Zhejiang Changming Chemical Products Co.,Ltd.
http://www.chemnet.com/ChinaSuppliers/15802/
China Suppliers > Changming >

powder coating

Details for powder coating

powder coating

Category:

Agrochemicals/Other pesticide
powder coating
CAS NO:
EC NO:
Molecular Formula:
Molecular Weight:
Specification:
Product description:
Introduction:
l          This type of thermosetting powder coatings are applicable to thermal transfer printing process.
l          The cured coating after the thermal transfer printing process, can be clear veins, beautiful color of patterns.
Applications:
Can be widely used in aluminum windows and doors, indoor metal furniture, security doors, car painting, etc.
Features:
This powder coating can reach the general performance requirements, the performance of its features are applicable to thermal transfer technology. The cured coating after the thermal transfer process, can be clear veins, beautiful color of patterns. And the thermal transfer film is easy to remove, no residual traces, can be adjusted according to the different thermal transfer process recipe to achieve the best results.
Technical Data:
Powder Property
Gravity
1.2~1.8g/cm3
Particle Size
General 30~38um，<64um >99%. If any special needs, can adjust
Volatile
〈1%
Soft Point
60~95℃ depend on the color and gloss
Fluidity
Good flow properties and transport properties
Storage Stability
Store under 30℃, with the shelf life of 12 months
 
Film Property
Coverage
8 -12 m 2 /Kg ， film thickness 70 μm （100% powder calculate）
Accelerated Aging
ASTM-G151
Pass
Impact
ASTM-D2794
Pass
Flexibility
ASTM-D4145
≤ 3 mm
Cup Convex
   GB/T 9753
>6mm
Adhesion
ASTM-D3359
0 Grade
Hardness
ASTM-D3363
>80
Poach
GB/T 1733/1993
No foaming, no color change
Acids
ASTM-D3260
Pass
Solvent
ASTM-D2248
Pass
Film Thickness
60-70μm
Salt Spray
ASTM-B117
1000 hours
Pass
Heat Resistant
GB/T 1740
1000 hours
Pass
Application Condition
Pretreatment
Steel
Phosphating
Inspection requirements of the pre-treatment testing once every two hours
Spray
This series of products for the following spray method: electrostatic spray; friction electrostatic spray;electrostatic fluidized bed coating (Require in advance); hot dipping fluidized bed (Require in advance);etc.
Note: the quality of the spray test at least once every two hours
Curing
Recommend 200℃ x 10 minutes, 180℃ x 15 minutes
      
 
Packing and Storage:
Polyethylene bag and paper carton, net weight: 20kg. Non-hazardous materials, can be transported by variety of ways. Should avoid direct sunlight and avoid damp heat, avoid contact with chemical substances.
 
Warranty Policy: The surface preparation and application procedures and other factors that affect performance are beyond our control.
Changming assumes no liability for coating failure other than to supply replacement material for the coating shown to be defective.
Do not use this product until the current material safety data sheet has been read and is fully understood. Changming shall not be liable for any injuries, damages or other losses deriving directly or in consequence of purshaser's use of product. Purchaser shall determine the suitability of this product for his own use, and thereby assumes all risks and liabilities in connection therewith.
Send your inquiry to powder coating supplier

Enter between 20 to 3,000 characters,English only.

Other products More>>
ChemNet  |   Product  |   Suppliers  |   Buy  |   Sell  |   News  |   REACH  |   Directory  |   CAS  |   Resource
ChemNet is a registered trademark of Zhejiang NetSun Co., Ltd.